This is TikiWiki 1.9.7 -Sirius- © 2002–2006 by the Tiki community Sun 24 of Sep, 2017 [12:08 UTC]

Forum: Hot Heads Tech Talk

Forums->Hot Heads Tech Talk->331 Intake Help

Wfrager
331 Intake Help


I have a 331 with the 6x2 Weiand intake and Stromburgs. I hate it. Never stays in tune. I want to convert to the Holley EFI, single TBI system. I noticed my heads do not have the coolant fittings. They run to the intake. What intake should I use? Do you make an intake with the water fittings?
  user offline
on: Tue 29 of Nov, 2016 [22:16 UTC] reads: 4228

Posted messages

Top
author message
BigD
user offline
Re: 331 Intake Help
on: Sun 11 of Dec, 2016 [12:59 UTC] score: 0.00
> I have a 331 with the 6x2 Weiand intake and Stromburgs. I hate it. Never stays in tune. I want to convert to the Holley EFI, single TBI system. I noticed my heads do not have the coolant fittings. They run to the intake. What intake should I use? Do you make an intake with the water fittings?

Want to sell the Weiand manifold?

author message
DaveBlakeman
user offline
Re: 331 Intake Help
on: Thu 08 of Dec, 2016 [18:48 UTC] score: 0.00
Check out Hot Heads pt # 21409 from that box you can feed into the HH manifold with heater hose and adapt a large rad hose .

author message
1930coupe
user offline
Re: 331 Intake Help
on: Wed 30 of Nov, 2016 [23:32 UTC] score: 0.00
> I have a 331 with the 6x2 Weiand intake and Stromburgs. I hate it. Never stays in tune. I want to convert to the Holley EFI, single TBI system. I noticed my heads do not have the coolant fittings. They run to the intake. What intake should I use? Do you make an intake with the water fittings?







Ive got 392 with 6 94's never have a problem with it. What part of it cant you get to stay tuned?

author message
Wfrager
user offline
Re: Re: 331 Intake Help
on: Fri 30 of Dec, 2016 [16:58 UTC] score: 0.00

> Ive got 392 with 6 94's never have a problem with it. What part of it cant you get to stay tuned?

Just noticed these replies. The car sat for a while, so maybe the carbs need a rebuild/cleaning. Looks like only the center two actually provide induction. There are no chokes at all. It is very hard to start and stalls constantly. When it does warm up, the idle is so high, it slams into gear. I just think a new TBI system would be a lot better....not as cool looking for sure.

author message
George
user offline
Re: Re: Re: 331 Intake Help
on: Fri 30 of Dec, 2016 [19:42 UTC] score: 0.00
>
. Looks like only the center two actually provide induction. There are no chokes at all. It is very hard to start and stalls constantly.

If you mean the front & rear carbs are blocked off, 2 strombergs is probably too little carb. The 2 center carbs should have chokes working, the outer ones don't. Set it up so the middle one work non-progressive & the outer ones progressive.

author message
Webmaster
user offline
Re: 331 Intake Help
on: Wed 30 of Nov, 2016 [13:14 UTC] score: 0.00
Wfrager:
Except for the Hot Heads Weber intake, all other Hot Heads intakes have a 1/2"NPT hole between the first and second port into the water jacket so you can run hoses to the remote thermostat block, then to the radiator. Hope this helps, Bob







> I have a 331 with the 6x2 Weiand intake and Stromburgs. I hate it. Never stays in tune. I want to convert to the Holley EFI, single TBI system. I noticed my heads do not have the coolant fittings. They run to the intake. What intake should I use? Do you make an intake with the water fittings?


Page: 1/1

Show posts: