This is TikiWiki 1.9.7 -Sirius- © 2002–2006 by the Tiki community Fri 28 of Jul, 2017 [18:52 UTC]

Forum: Hot Heads Tech Talk

Forums->Hot Heads Tech Talk->poly ID help needed

cambratrod
poly ID help needed


I am needing help to ID a polyhead.
The stamped Id numbers are D67-3509C.
It was in a ratrod that I purchased a few years back so I do not know application/year or CI.
It is also equipped with hyd lifters which I am looking to replace as well as a new camshaft and timing chain.
It is mated to a cast iron torqueflight and also has what appears to be a factory 4bbl intake and carb.
  user offline
on: Mon 27 of Mar, 2017 [13:44 UTC] reads: 1718

Posted messages

Top
author message
George
user offline
Re: poly ID help needed
on: Mon 08 of May, 2017 [01:26 UTC] score: 0.00
> It is also equipped with hyd lifters .

I'm thinking all the A polys were solid cam......

author message
George
user offline
Re: poly ID help needed
on: Wed 29 of Mar, 2017 [01:35 UTC] score: 0.00
If you haven't already, you might post this on www.forwardlook.net

author message
ron37
user offline
Re: poly ID help needed
on: Wed 29 of Mar, 2017 [00:59 UTC] score: 0.00
I saw some info that the 57 Dodge from Canada had a 313 Poly with a D67 mark along with several other designations. Also they also had a 354 with the same number. Best bet is to take the numbers off the intake. That will tell if it is a low or tall deck. Also will tell if it is a Dodge or Chrysler.

author message
cambratrod
user offline
Re: Re: poly ID help needed
on: Mon 08 of May, 2017 [00:15 UTC] score: 0.00
> I saw some info that the 57 Dodge from Canada had a 313 Poly with a D67 mark along with several other designations. Also they also had a 354 with the same number. Best bet is to take the numbers off the intake. That will tell if it is a low or tall deck. Also will tell if it is a Dodge or Chrysler.


Sorry for the delay.
Intake number is 1619826
Head number is 1618721-1

author message
George
user offline
Re: poly ID help needed
on: Tue 28 of Mar, 2017 [17:40 UTC] score: 0.00
What's the part # on the intake?

author message
cambratrod
user offline
Re: Re: poly ID help needed
on: Mon 08 of May, 2017 [00:19 UTC] score: 0.00
> What's the part # on the intake?

Sorry for the delay.
Intake number is 1619826
Head number is 1618721-1

author message
George
user offline
Re: Re: Re: poly ID help needed
on: Mon 08 of May, 2017 [01:24 UTC] score: 0.00
> > What's the part # on the intake?
>
> Sorry for the delay.
> Intake number is 1619826
> Head number is 1618721-1


OK, you have a Plymouth A (non hemi based) Poly. The intake is for a '56 277 4V. The heads are for a '55 303 or a 57-8 318.

author message
George
user offline
Re: Re: Re: Re: poly ID help needed
on: Tue 09 of May, 2017 [23:24 UTC] score: 0.00
>
> OK, you have a Plymouth A (non hemi based) Poly. The intake is for a '56 277 4V. The heads are for a '55 303 or a 57-8 318.

Guess wwe need the block number to know.

author message
cambratrod
user offline
Re: Re: Re: Re: Re: poly ID help needed
on: Sun 28 of May, 2017 [20:37 UTC] score: 0.00
> >
> > OK, you have a Plymouth A (non hemi based) Poly. The intake is for a '56 277 4V. The heads are for a '55 303 or a 57-8 318.
>
> Guess wwe need the block number to know.

Block #1876329


author message
George
user offline
Re: Re: Re: Re: Re: Re: poly ID help needed
on: Fri 09 of Jun, 2017 [03:47 UTC] score: 0.00
>
> Block #1876329
>

Doesn't show in my refs.

author message
George
user offline
Re: poly ID help needed
on: Tue 28 of Mar, 2017 [17:39 UTC] score: 0.00
D 67 shows up as a model number for a '57 Dodge, but that shouldn't be on the engine, I'd think.

author message
DaveBlakeman
user offline
Re: poly ID help needed
on: Tue 28 of Mar, 2017 [16:27 UTC] score: 0.00
Searching all the Mopar ID websites I don't see anything with that prefix. Is this a Dodge?


Page: 1/1

Show posts: